The advantages of split type connection diagram to slant bed CNC lathe design
The advantages of the system connection diagram to slant bed CNC lathe design release date: 2018 - 12 - 06 clicks: 2758 slant bed CNC lathe split type connection design: the advantages of gate body and setting, a body under the seat on the body has a fixed, seated on the body has the connection, by positioning screw is fixed at a fixed part has at least two positioning block, connection of the surface depend on the fixed part of the above, the connection of the lateral surface depend on the positioning block, by retaining bolt will connect on the fixed part, make convenient production base. Set at a fixed part shoulder, convenient locating piece installation. Set up the installation groove, convenient for the installation of the retaining bolt. Set the connection bolts, set fixed and connected before, before make the base of the whole stability is good. Slant bed CNC lathe split type connection design as shown in the figure below: 1, the seat body; the image of 1 a, fixed; 1 a1, retaining shoulder; 1 b, the former fixed department; 2, the gate body; 2 a, lathe bed inclined plane; 2 b, connection; 2 b1, installation groove; 2 c, first connection; 3, positioning block; 4, positioning bolt; 5, fixed bolts; 6, connecting bolts. As shown, the machine tool base, including the setting of 1 and table 2, a body under the gate body set up have a lathe bed inclined plane 2 a. 1 a body under the table has a bulge on the surface of the fixed part of the 1 a, 1 a body under the above-mentioned surface also have and fixed part 1 a corresponding set out before the fixed part of the 1 b. The lower end of the table body 2 first connection with connection of 2 b and 2 c. Under the connection of 2 b surface to depend on the fixed part 1 a above, connection of 2 b through multiple fixed bolt is fixed on the fixed part 1 a; Connection of 2 c before landing on the surface in the former fixed department 1 b on the table, and before the connection of 2 c and 1 b through fixed department before the fixed bolt connection. Set on the side of the connection of 2 b surface with the retaining bolt installation of one-to-one slot 2 b1, installed on the sidewalls of the slot 2 b1 runs down mounting holes, the retaining bolt 5 through the mounting holes and fixed 1 a threaded connection, the retaining bolt 5 head inside the installation groove 2 b1. Fixed part 1 a connection has at least two positioning block 3, positioning block 3 through 4 fixed positioning bolt connection on the fixed part 1 a fixed set of 1 a table surface has a shoulder 1 a1, the positioning block 3 under surface on depend on the fixed part 1 a above, the positioning block 3 side surface on against the shoulder block 1 a1, each positioning block 3 set has at least two positioning bolt 4. Rely on the side of the connection of 2 b surface positioning block 3 on the inside of the face. Positioning block 3 have connection hole on the outside of the Settings, connection hole set bolt in the next 6, the tail end of the connecting bolts 6 wear out the medial aspect of the locating piece 3 and 2 b threaded connection department, the head of the joint bolt 6 department to depend on the outer edge of the locating piece 3 surface. Make processing base, can be separated from the casting under the seat body 1 and table 2, the casting is convenient, machining lathe bed inclined plane 2 a party then. Assembly gate body 2, and 1, a body under the first positioning block 3 by positioning bolt 4 fixed on the fixed part 1 a, then place the body 2 attendance on the fixed part 1 a above, make the body connection department attendance 2 b landing on the surface of the surface on the fixed part 1 a, and make the connection of 2 b side landing on the surface in the positioning block 3 on the inside of the face, then by connecting bolt 6 make gate body 2 and positioning block 3 fixed connection, and then through the fixed bolt 5 body 2 fixed in the next seat body 1 attendance. Gate body 2, and 1 set after fission, a body under the through fixed department again after 1 a and positioning block 3 fixed connection, convenient production makes the machine base.